Orbital Sander Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device. Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin. Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör dig bekant med apparatens/maskinens funktioner. Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner. Slå opp siden med illustrasjoner før bruksanvisningen leses. Bli først kjent med alle apparatets funksjoner. , . Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut. XQ600 Orbital Sander Kompernaß GmbH Burgstraße 21 44867 Bochum (Germany) Operation and Safety Notes epäkeSkOhiO makOne Käyttö- ja turvallisuusohjeet excenterSlipmaSkin ekSenterSliper Bruksanvisning och säkerhetsanvisningar Last Information Update · Tietojen tila · Informationsstatus · Tilstand af information · Opplysningenes gyldighet · · Stand der Informationen: 11 / 2007 · Ident.-No.: XQ600112007-3 excenterSliber Brugs- og sikkerhedsanvisninger Betjenings- og sikkerhetshenvisninger GB / IE / CY FI SE DK NO GR / CY DE / AT Operation and Safety Notes Käyttö- ja turvallisuusohjeet Bruksanvisning och säkerhetsanvisningar Brugs- og sikkerhedsanvisninger Betjenings- og sikkerhetshenvisninger Bedienungs- und Sicherheitshinweise Page Sivu Sidan Side Side Seite 5 15 23 31 41 49 59 excenterSchleifer Bedienungs- und Sicherheitshinweise 10 1 2 3 9 8 7 65 4 a B C d 11 Table of Content Introduction Intended utilisation ..................................................................................................... Features and Fittings................................................................................................... Items supplied ............................................................................................................. Technical data............................................................................................................. Page Page Page Page 6 6 6 7 General safety advice Your working area ...................................................................................................... Electrical safety ........................................................................................................... Personal safety............................................................................................................ Careful handling and use of electrical power tools ................................................ Safety advice relating specifically to random orbital sanders ............................... Original accessories / tools ....................................................................................... Understood everything?............................................................................................. Page 7 Page 7 Page 8 Page 8 Page 9 Page 9 Page 10 Before use Changing sanding sheets ......................................................................................... Page 10 Selecting rotation speeds and sanding sheets ....................................................... Page 10 Commissioning Switching on and off .................................................................................................. Page 10 Dust suction ................................................................................................................. Page 11 Advice about ways of working when sanding......................................................... Page 12 Maintenance and Cleaning ..................................................................... Page 12 Disposal .................................................................................................................... Page 12 Information Servicing...................................................................................................................... Page 12 Declaration of conformity / Manufacturer................................................................ Page 13 GB/IE/CY 5 Introduction The following icons / symbols are used in this instruction manual: Read instruction manual! Safety class II Observe caution and safety notes! Proper procedure and handling. Caution ­ electric shock! Dangerous electric current ­ danger to life! Wear hearing protection, dust protection mask, protective glasses and protective gloves. Keep children and other unauthorised personnel at a safe distance when using electrical tools. Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock. Damaged appliances, power cables and power plugs mean potentially fatal risks from electric shock. Regularly check the condition of the appliance, the power cables and the power plugs. Dispose packaging and appliance in an environmentally-friendly way! Explosive material! V~ W n0 Voltage Watts (Effective power) Rated idle running speed Rotary Sander XQ 600 Sanding of large areas. For wood, plastics and metal Q This appliance is not intended for commercial applications. Q Introduction Features and Fittings Handswitch DUO-START On / Off switch Locking button Dust collection box Adjusting wheel - rotation speed selector Release button - dust collection box Suction ring Sanding plate Sanding pad Front switch DUO-START Adaptor for external dust suction (Fig. D) Please make sure you familiarise yourself fully with the way the device works before you use it for the first time and that you understand how to handle electrical power tools correctly. Further details can be found in the operating instructions. Keep these instructions in a safe place. If you pass the device on to anyone else, please ensure that you also pass on all the documentation. Q Intended utilisation 1 2 3 4 5 6 7 8 9 10 11 The appliance is suitable for the dry sanding and buffing of wood, metal and paint. Any other uses, and modifications to the appliance, are deemed to be improper usage and may result in serious physical injury. The manufacturer will not accept liability for loss or damage arising from improper use. 6 GB/IE/CY Q Items supplied Rotary Sander XQ 600 Sanding sheets (1x Grit 80, 1x Grit 120) Dust collection box Suction adaptor 1 2 1 1 Introduction / General safety advice 1 Operating manual 1 Booklet "Warranty and Service" Q Technical data XQ 600 KH 3168 230 V ~ 50 Hz · 600 W 2.500-8.000 min-1 Schwingzahl: 5.000-16.000 min-1 Date of manufacture: 02-2008 Rated voltage: 230 V ~ 50 Hz Rated power: 600 W Nominal oscillations: n0 5.000 - 16.000 min-1 Nominal revolutions: n0 2.500 - 8.000 min-1 Excentricity: 5 mm Sanding plate: ø 150 mm Protection class: II / Noise and vibration data: Values determined in accordance with EN 60745 The sound pressure level (A-weighted) of the device is typically 84 dB(A). Uncertainty K=3 dB. The sound level while working can exceed 85 dB (A). Wear ear protection! Evaluated acceleration, typical: Hand / arm vibration ah = 2,309 m / s2 Uncertainty K = 1,5 m / s2 WaRNING! The vibration level given in these instructions has been measured in accordance with a standardised measurement procedure specified in EN 60745 and can be used to compare devices. Different uses of the device give rise to different vibration levels and in many cases they may exceed the values given in these instructions. It is easy to underestimate the vibration load if the electrical power tool is used regularly in particular circumstances. Note: If you wish to make an accurate assessment of the vibration loads experienced during a particular period of working, you should also take into account the intervening periods of time when the device is switched off or is running but is not actually in use. This can result in a much lower vibration load over the whole of the period of working. Kompernaß GmbH · 44867 Bochum Germany · www.kompernass.de General safety advice J aTTENTIoN! Please read all the instructions and advice. Failure to observe the instructions and advice given below may result in electric shock, fire and / or serious injury. MAKE SURE THAT YOU KEEP THESE INSTRUCTIONS AND SAFETY ADVICE IN A SAFE PLACE. 1. Your working area a) Keep your working area clean and clutter-free. Untidy or poorly lit working areas can lead to accidents. b) Do not work with the device in potentially explosive environments in which there are inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes. c) Keep children and other people away while you are operating the electrical tool. Distractions can cause you to lose control of the device. 2. Electrical safety a) The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock. GB/IE/CY 7 General safety advice b) avoid touching earthed surfaces such as pipes, radiators, ovens and refrigerators with any part of your body. There is an increased risk of electric shock if your body is earthed. c) Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock. d) Do not use the mains lead for any purpose for which it was not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat, oil, sharp edges or moving parts of the device. Damaged or tangled mains leads increase the risk of electric shock. e) When working outdoors with an electrical power tool always use extension cables that are also approved for use outdoors. The use of an extension cable suitable for outdoor use reduces the risk of electric shock. f) Use a residual current device (RCD) for protection if operating the electrical power tool in a moist environment is unavoidable. The use of an RCD reduces the risk of electric shock. c) avoid unintentional operation of the device. Make sure that the switch is in the "oFF" position before you insert the mains plug into the mains socket. Accidents can happen if you carry the device with your finger on the switch or you have already switched the device on before you connect it to the mains. d) Remove any setting tools or spanners before you switch the device on. A tool or spanner left attached to a rotating part of a device can lead to injury. e) Do not overestimate your own abilities. Keep proper footing and balance at all times. By doing this you will be in a better position to control the device, especially in unforeseen circumstances. f) Wear suitable clothing. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves clear of moving parts. Loose clothing, jewellery or long hair can become trapped in moving parts. g) If vacuum dust extraction and collection devices are fitted do not forget to check that they are properly connected and correctly used. The use of these devices reduces the hazard presented by dust. 3. Personal safety a) Remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury. b) Wear personal protective equipment and always wear safety glasses. The wearing of personal protective equipment such as dust masks, non-slip safety shoes, safety helmets or ear protectors, appropriate to the type of electrical power tool used and work undertaken, reduces the risk of injury. 4. Careful handling and use of electrical power tools a) Do not overload the device. always use an electrical power tool that is intended for the task you are undertaking. By using the right electrical power tool for the job you will work more safely and achieve a better result. b) Do not use an electrical power tool if its switch is defective. An electrical power tool that can no longer be switched on and off is dangerous and must be repaired. c) When not in use always ensure that electrical power tools are kept out of reach of children. Do not let anyone use the device if he or she is not familiar with it or has not read the instructions and advice. Electrical power tools are dangerous when they are used by inexperienced people. 8 GB/IE/CY General safety advice d) Look after the device carefully. Check that moving parts are working properly and move freely. Check for any parts that are broken or damaged enough to detrimentally affect the functioning of the device. Have damaged parts repaired before you use the device. Many accidents have their origins in poorly maintained electrical power tools. e) Keep cutting tools clean and sharp. Carefully maintained c ...